New OTC Catalog Features Time-Saving Tools And Equipment | Plastic Measuring Tool

“Composites and fire: developments and new trends in flame-retardant additives” by Belén Redondo, Composites Department of AIMPLAS, Plastics Technology Centre, Valencia, Spain.

However, the Miami product has missed significant time because of injuries over the last four seasons.

The Offset Extension Wrench (part number FRW10) provides 10” of reach, making it easier for technicians to loosen or tighten hard-to-grasp fasteners that are buried in assemblies.

Stupid is not using the quality of the engineering the manufacturer shows you to extrapolate the quality of the engineering that you can’t see.

Google voice came out after siri but it’s still a ton better at getting me what I want through voice commands and integrating better with phone features. Apple tighter tolerances and better build quality somehow didn’t stop them from creating a bigger better antenna in the iPhone 4 that did the exact opposite and dropped more calls. OF course they denied it was even a problem for a while first. That’s some darn good quality control.

As a technician for the last 20 years, I can tell you that modern Apple design “IS HORRIBLE!!!” From the basic layout, to the final engineering, Apple products suck! Got a nice picture of a stock heatsink in a late model Macbook where 25% of the die surface area is exposed due to poor heatsink design. The charging circuit on Macbooks are also so over complicated it’s a freaking nightmare to diagnose and repair(when even possible). Apple has fallen a long way since it’s golden years before Steve Jobs came back and drove Apple off a steep cliff. Anyone remember their “snow white” design theme? Those were great times! When an entire Macintosh could be taken apart without using any tools, now THAT’s great engineering, and forethought. The PCB designs were also so much more simple back then and better designed, to last. You can still find plenty of old Mac’s and Powerbooks still humming along just fine 2 decades later, but a Macbook? Yeah good luck keeping that POS working past about 2 years, right after your Apple care warranty expires your ATi GPU will de-solder itself from the board due to excessive heat cycle’s caused by bad engineering. To each his/her own my friend.

Stacking the rotation with shooters puts pressure on defenses in a lot of the same ways adding another scorer does. Utah is better off with a reliable go-getter off the dribble, but drowning the Gobert-Mitchell two-man game in off-ball snipers is the next best thing—and bound to come cheaper.

Milwaukee says that these will be the highest torque cordless ratchets on the market, delivering up to 60 ft-lbs of torque. They also aim to deliver the most compact head design on the market. By providing these new ratchets with Powerstate brushless motors, Milwaukee promises they will last two times longer than their brushed competition.

At a garage sale a number of years ago, I bought a coffee can with a lot of lag bolts in it for $2. When I got home and emptied out the can, the bolts/screws in the bottom 2/3rds of the can were rusty, freshly painted with silver paint! B^)

All right, so it’s not the timing light. Consider what could have changed/gone south during your cylinder-head swap. If the cam and rocker ratio are the same as before, idle vacuum should remain about the same at the same base timing, or—due to a higher static compression ratio generated by the new heads’ smaller combustion chambers—be even slightly higher. This assumes the valves and the carb’s idle mixture and idle speed are properly adjusted. A misadjusted carburetor, excessively tight valve lash, and/or a vacuum leak could require way over-advancing the timing to crutch the underlying fault so the car seems to run a little smoother. Therefore, you need to get these items squared away at the normal base timing range.

“We do a lot of testing for companies looking to see how their products perform,” says Tobias Aldrete, the shop’s general manager. “We’ve done testing for AFR and Edelbrock, etc. This engine is just about testing carb versus EFI in a real world scenario with different camshafts. AFR came to us about new intakes for the Windsor, so we figured we might as well put it all in the mix.”

The new tool display is free when purchasing any five SP Air tools. SP Air’s tool lineup includes impact wrenches, impact drivers, ratchet wrenches, die grinders, sanders and drills.